Forum

Forumlar
Microsoft
Windows Server
Failover Cluster Do...
 
Bildirimler
Hepsini Temizle

Failover Cluster Domain'e Erişim Problemi

 
Windows Server
Son Cevaplar gön: Can Bolat 11 yıl önce
3 Yazılar
2 Üyeler
0 Reactions
550 Görüntüleme
RSS
 Alper AKAY
(@AlperAKAY)
Gönderiler: 4
Active Member
Konu başlatıcı
 

Merhabalar,

Windows Server 2012 failover cluster kurdum. SQL Server 2012 cluster kurarken, servis accountlarını set ederken domain user'ını bulamadı. Browse dediğimde domaini görmediğini fark ettim. Local Users and Groups'a girip herhangi bir gruba domain user eklemek istediğimde Locations'da domain yok. 

Cmd'den komutla local gruba domain user ekleyebiliyorum.

 Daha önce file server cluster kurmuştum.Makinaları kontrol ettiğimde aynı durumu orada da gördüm. File serve clusterr sorunsuz çalışıyor.

Domaini görmediği için SQL Server cluster kuramadım.

 Fail over cluster'da böyle bir durumun sebebi nedir?

 Aşağıdaki linkte Windows Server 2000 için böyle bir şey sorulmuş:

  http://www.experts-exchange.com/Networking/Windows_Networking/Q_20829920.html

Yardımlarınızı rica ederim.

 

Teşekkürler

 
Gönderildi : 26/07/2013 01:13

 Alper AKAY
(@AlperAKAY)
Gönderiler: 4
Active Member
Konu başlatıcı
 

Cluster'ı stop edip.Node'ları tek tek domainden çıkarıp tekrar ekledim.Düzeldi.

 

Teşekkürler

 
Gönderildi : 26/07/2013 13:15

 Can Bolat
(@canbolat)
Gönderiler: 1253
Noble Member
 

Geri bildirim için teşekkürler.Yaşadığınız sorun dns problemine benziyordu.Ethernet kartlarının öncelik sırasıda buna etki edebilir diye düşünüyorum.

 

Usage Number of Network Cards Comments
Management Network(Parent Partition) 1 Network Card
  • Make sure this card is listed first in the Adapter and Bindings connection order.
  • In Failover Cluster Manager make sure that the NIC is configured to allow cluster network communication on this network.
  •  
  • This will act as a secondary connection for the Heartbeat.
Storage ISCSI 2 Network Cards - Not Teamed
  • Enable MPIO.
  • Disable NetBIOS on these interfaces
  • Do not configure a Gateway
  • Do not configure a DNS server
  • Make sure that each NIC is NOT set to register its connection in DNS
  • Remove File and Printer sharing
  • Do not remove Client from Microsoft networks if using Netapp Snapdrive with RPC authentication
  • In Failover Cluster Manager select- Do not allow cluster network communication on this network
VM Network
(Parent Partition)		 2 Network cards :
1 for Dynamic IP’s
1 for Reserved IP’s
  • Disable NetBIOS on these interfaces
  • Do not configure a Gateway
  • Do not configure a DNS server
  • Make sure that each NIC is NOT set to register its connection in DNS
  • Remove File and Printer sharing and Client from Microsoft networks
  • In Failover Cluster Manager select - Do not allow cluster network communication on this network.
Cluster Heartbeat 1 Network Card
  • Disable NetBIOS on this interface
  • Do not configure a Gateway
  • Do not configure a DNS server
  • Make sure that this NIC is NOT set to register its connection in DNS
  • Make sure that Client for Microsoft Networks and File and Printer Sharing for Microsoft Networks are enabled to support Server Message Block (SMB), which is required for CSV.
  • In Failover Cluster Manager make sure that the NIC is configured to allow cluster network communication on this network.
  • In Failover Cluster Manager remove the tick box for Allow Clients Connect through this network. This setting has nothing to do with the host/parent partition. This setting is used to control over what NICs the Cluster Resources can be accessed.
Cluster Shared Volume (CSV) 1 Network Card
  • Disable NetBIOS on this interface
  • Make sure that this NIC is NOT set to register its connection in DNS
  • Make sure that Client for Microsoft Networks and File and Printer Sharing for Microsoft Networks are enabled to support Server Message Block (SMB), which is required for CSV.
  • In Failover Cluster Manager remove the tick box for Allow Clients Connect through this network. This setting has nothing to do with the host/parent partition. This setting is used to control over what NICs the Cluster Resources can be accessed. This is more relevant for other workloads e.g. File Cluster. It has no impact on the communication with the host partition or for the VM's themselves.
  • By default the cluster will automatically choose the NIC to be used for CSV communication. We will change this later.
  • This traffic is not routable and has to be on the same subnet for all nodes.
Live Migration 1 Network Card
  • Disable NetBIOS on this interface
  • Make sure that this NIC is NOT set to register its connection in DNS.
  • In Failover Cluster Manager remove the tick box for Allow Clients Connect through this network. This setting has nothing to do with the host/parent partition. This setting is used to control over what NICs the Cluster Resources can be accessed. This is more relevant for other workloads e.g. File Cluster. It has no impact on the communication with the host partition or for the VM's themselves.
  • By default the cluster will automatically choose the NIC to be used for Live-Migration. You can select multiple networks for LM and give them a preference.
 
Gönderildi : 26/07/2013 20:06

Forum Jump:
  Önceki Konu
Sonraki Konu  
Paylaş: