Forum
Bildirimler
Hepsini Temizle
System Center Yönetim Ailesi
5
Yazılar
2
Üyeler
0
Reactions
459
Görüntüleme
Konu başlatıcı
Merbaha;
DPM 2010 da protection grup içerisine bir mamber daha eklemek istediğim zaman mmc stopped working hatası almakta ve ardındanda servis kapanmaktadır. eventlerde aldığım hata aşağıdaki gibidir.Konu ile ilgili yardımlarınızı rica ederim.
The description for Event ID 999 from source MSDPM cannot be found. Either the component that raises this event is not installed on your local computer or the installation is corrupted. You can install or repair the component on the local computer.
If the event originated on another computer, the display information had to be saved with the event.
The following information was included with the event:
An unexpected error caused a failure for process 'mmc'. Restart the DPM process 'mmc'.
Problem Details:
<FatalServiceError><__System><ID>19</ID><Seq>1</Seq><TimeCreated>17.05.2012 09:36:09</TimeCreated><Source>DpmThreadPool.cs</Source><Line>163</Line><HasError>True</HasError></__System><ExceptionType>NullReferenceException</ExceptionType><ExceptionMessage>Object reference not set to an instance of an object.</ExceptionMessage><ExceptionDetails>System.NullReferenceException: Object reference not set to an instance of an object.
at System.Windows.Forms.ListView.ListViewNativeItemCollection.get_Item(Int32 displayIndex)
at System.Windows.Forms.ListView.ListViewItemCollection.get_Item(Int32 index)
at System.Windows.Forms.ListView.ListViewNativeItemCollection.Clear()
at System.Windows.Forms.ListView.ListViewItemCollection.Clear()
at System.Windows.Forms.ListView.Dispose(Boolean disposing)
at System.ComponentModel.Component.Dispose()
at System.Windows.Forms.Control.Dispose(Boolean disposing)
at System.ComponentModel.Component.Dispose()
at System.Windows.Forms.Control.Dispose(Boolean disposing)
at System.ComponentModel.Component.Dispose()
at System.Windows.Forms.Control.Dispose(Boolean disposing)
at System.ComponentModel.Component.Dispose()
at System.Windows.Forms.Control.Dispose(Boolean disposing)
at System.Windows.Forms.ContainerControl.Dispose(Boolean disposing)
at Microsoft.Internal.EnterpriseStorage.Dls.UI.Dpw.ClientsSelectionPage.Dispose(Boolean disposing)
at System.ComponentModel.Component.Dispose()
at Microsoft.Internal.EnterpriseStorage.Dls.UI.Dpw.PageCache.Dispose()
at Microsoft.Internal.EnterpriseStorage.Dls.UI.Dpw.DataProtectionWizard.Dispose(Boolean disposing)
at System.ComponentModel.Component.Finalize()</ExceptionDetails></FatalServiceError>
the message resource is present but the message is not found in the string/message table
Gönderildi : 17/05/2012 15:38
Merhaba;
DPM DB' si local sunucu üzerinde midir ? ve PG eklemek istediğiniz makinelerin agentlarını baştan yüklermisiniz?
Gönderildi : 17/05/2012 16:50
Konu başlatıcı
Fatih Bey Merhaba;
Öncelikle desteğiniz için teşekkür ederim.DPM DB sunucusu localde bulunmaktır.İlgili clientın angetını yeniden yüklemeye kalktığım zamanda aynı mmc ile ilgili aynı hatayı almaktayım.
Gönderildi : 17/05/2012 16:54
Merhaba
DPM sunucusu ile client arasında aşağıda ki port numaraları konuşuyor mu ?
| rotocol | Port | Details |
|---|---|---|
|
DCOM |
135/TCP |
The DPM control protocol uses DCOM. DPM issues commands to the protection agent by invoking DCOM calls on the agent. The protection agent responds by invoking DCOM calls on the DPM server. TCP port 135 is the DCE endpoint resolution point used by DCOM. By default, DCOM assigns ports dynamically from the TCP port range of 1024 through 65535. However, you can configure this range by using Component Services. For more information, see Using Distributed COM with Firewalls ( http://go.microsoft.com/fwlink/?LinkId=46088). Note that for DPM-Agent communication you must open the upper ports 1024-65535. To open the ports, perform the following steps:
|
|
TCP |
5718/TCP |
The DPM data channel is based on TCP. Both DPM and the protected computer initiate connections to enable DPM operations such as synchronization and recovery. DPM communicates with the agent coordinator on port 5718 and with the protection agent on port 5719. |
|
DNS |
53/UDP |
Used between DPM and the domain controller, and between the protected computer and the domain controller, for host name resolution. |
|
Kerberos |
88/UDP 88/TCP |
Used between DPM and the domain controller, and between the protected computer and the domain controller, for authentication of the connection endpoint. |
|
LDAP |
389/TCP |
Used between DPM and the domain controller for queries. |
|
NetBIOS |
137/UDP |
Used between DPM and the protected computer, between DPM and the domain controller, and between the protected computer and the domain controller, for miscellaneous operations. Used for SMB directly hosted on TCP/IP for DPM functions. |
Gönderildi : 17/05/2012 17:56
Konu başlatıcı
Fatih Bey Merhaba;
Görüşmeleri kontrol ettim bir sıkıntı bulunmamaktadır.Yaklaşık bir yıldır çalışan bir sistemdir.Bugün yeni bir client ortama katılınca onu PG içine eklemek istediğim zaman mmc has stopped working hatası almaktayım.
v\:* {behavior:url(#default#VML);}
o\:* {behavior:url(#default#VML);}
w\:* {behavior:url(#default#VML);}
.shape {behavior:url(#default#VML);}
Normal
0
21
false
false
false
TR
X-NONE
X-NONE
MicrosoftInternetExplorer4
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Normal Tablo";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman","serif";}
Gönderildi : 17/05/2012 18:06
