snmp açılımı

Merhaba 

This example shows how to enable all versions of SNMP. The configuration permits any SNMP manager to access all objects with read-only permissions using the community string public. This configuration does not cause the switch to send any traps.

Switch(config)# snmp-server community public

This example shows how to permit any SNMP manager to access all objects with read-only permission using the community string public. The switch also sends VTP traps to the hosts 192.180.1.111 and 192.180.1.33 using SNMPv1 and to the host 192.180.1.27 using SNMPv2C. The community stringpublic is sent with the traps.

Switch(config)# snmp-server community public

Switch(config)# snmp-server enable traps vtp

Switch(config)# snmp-server host 192.180.1.27 version 2c public

Switch(config)# snmp-server host 192.180.1.111 version 1 public

Switch(config)# snmp-server host 192.180.1.33 public

This example shows how to allow read-only access for all objects to members of access list 4 that use the comaccess community string. No other SNMP managers have access to any objects. SNMP Authentication Failure traps are sent by SNMPv2C to the host cisco.com using the community string public.

Switch(config)# snmp-server community comaccess ro 4

Switch(config)# snmp-server enable traps snmp authentication

Switch(config)# snmp-server host cisco.com version 2c public

This example shows how to send Entity MIB traps to the host cisco.com. The community string is restricted. The first line enables the switch to send Entity MIB traps in addition to any traps previously enabled. The second line specifies the destination of these traps and overwrites any previous snmp-server host commands for the host cisco.com.

Switch(config)# snmp-server enable traps entity 

Switch(config)# snmp-server host cisco.com restricted entity

This example shows how to enable the switch to send all traps to the host myhost.cisco.com using the community string public:

Switch(config)# snmp-server enable traps

Switch(config)# snmp-server host myhost.cisco.com public

This example shows how to associate a user with a remote host and to send auth (authNoPriv) authentication-level informs when the user enters global configuration mode:

Switch(config)# snmp-server engineID remote 192.180.1.27 00000063000100a1c0b4011b

Switch(config)# snmp-server group authgroup v3 auth

Switch(config)# snmp-server user authuser authgroup remote 192.180.1.27 v3 auth md5 
mypassword

Switch(config)# snmp-server user authuser authgroup v3 auth md5 mypassword

Switch(config)# snmp-server host 192.180.1.27 informs version 3 auth authuser config

Switch(config)# snmp-server enable traps

Switch(config)# snmp-server inform retries 0

Kaynak:Cisco 

teşekkürederim ama ben switch de snmp serverri kurmak istemiyorum 
snmp yi microsoft servere kurmak istiyorum 
böyle bir durumda kenar switchlere nasıl bir konfigürasyon yapmam gerekıyor.

teşekkürederim ama ben switch de snmp serverri kurmak istemiyorum 
snmp yi microsoft servere kurmak istiyorum 
böyle bir durumda kenar switchlere nasıl bir konfigürasyon yapmam gerekıyor.

rica ederim.

yukarıdaki konfigürsayon örnek bir snmp uygulamasıdır. siz sadece burada server ip sini karşılayan kısma kendi MS üzerine kurduğunuz snmp server ip sini karşılık görebilirsiniz. 

Sadece küçük bir hatırlatmada bulunmak isterim. SNMP Community Name kısmını güvenlik için kesinlikle "public" yapmayın. Mümkünse sadece sizin tahmin edebileceğiniz karmaşık bir community name kullanın.