Juniper SRX 210 Boot Error

Merhaba

 Juniper SRX 210 başlangıçta hata vermektedir.

U-Boot 1.1.6-JNPR-1.7 (Build time: May  4 2010 - 06:59:58)

SRX_210_HIGHMEM board revision major:1, minor:46, serial #: AADM1528
OCTEON CN5020-SCP pass 1.1, Core clock: 400 MHz, DDR clock: 200 MHz (400 Mhz data rate)
DRAM:  1024 MB
Starting Memory POST...
Checking datalines... OK
Checking address lines... OK
Checking 512K memory for U-Boot... OK.
Running U-Boot CRC Test... OK.
Flash:  4 MB
USB:   dwc_otg_core_reset() HANG! Soft Reset GRSTCTL=80000001
scanning bus for devices... 1 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found
Clearing DRAM........ done
BIST check passed.
Starting PCI
PCI Status: PCI 32-bit
PCI BAR 0: 0xf8000000, PCI BAR 1: Memory 0x00000000  PCI 0x00000000
Boot Media: nand-flash usb
Net:   octeth0
POST Passed
Press SPACE to abort autoboot in 1 seconds
ELF file is 32 bit
Loading .text @ 0x8f000078 (246092 bytes)
Loading .rodata @ 0x8f03c1c4 (13940 bytes)
Loading .rodata.str1.4 @ 0x8f03f838 (16580 bytes)
Loading set_Xcommand_set @ 0x8f0438fc (104 bytes)
Loading .rodata.cst4 @ 0x8f043964 (20 bytes)
Loading .data @ 0x8f044000 (5620 bytes)
Loading .data.rel.ro @ 0x8f0455f4 (120 bytes)
Loading .data.rel @ 0x8f04566c (136 bytes)
Clearing .bss @ 0x8f0456f8 (11912 bytes)
## Starting application at 0x8f000078 ...
Consoles: U-Boot console 
Found compatible API, ver. 1.7

FreeBSD/MIPS U-Boot bootstrap loader, Revision 1.7
([email protected], Tue May  4 07:15:51 UTC 2010)
Memory: 1024MB
[3]Booting from nand-flash slice 1
Un-Protected 1 sectors
writing to flash...
Protected 1 sectors

can't load '/kernel'

can't load '/kernel.old'

Press Enter to stop auto bootsequencing and to enter loader prompt.

Type '?' for a list of commands, 'help' for more detailed help.
loader> 

Çözüm olarak deneme yapılan işlemlerden birisi junos yüklemesi yapmak oldu fakat sonuç olumsuz.

loader> set ipaddr=10.20.30.8

loader> set netmask=255.255.255.240

loader> set serverip=10.20.30.5

loader> install tftp://10.20.30.5/junos-srxsme-12.1X46-D15.3-domestic.tgz
octeth0: Up 1000 Mbps Full duplex (port  0)
|/-\|/-/kernel data=0xb0f9c0+0x134788 \ syms=[0x4+0x8b320/+0x4+0xc9df5/
Kernel entry at 0x801000e0 ...
init regular console
Primary ICache: Sets 64 Size 128 Asso 4
Primary DCache: Sets 1 Size 128 Asso 64
Secondary DCache: Sets 128 Size 128 Asso 8
GDB: debug ports: uart
GDB: current port: uart
KDB: debugger backends: ddb gdb
KDB: current backend: ddb
kld_map_v: 0x8ff80000, kld_map_p: 0x0
Copyright (c) 1996-2014, Juniper Networks, Inc.
All rights reserved.
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
    The Regents of the University of California. All rights reserved.
JUNOS 12.1X46-D15.3 #0: 2014-02-26 01:06:38 UTC
    [email protected]:/volume/build/junos/12.1/service/12.1X46-D15.3/obj-octeon/junos/bsd/kernels/JSRXNLE/kernel
JUNOS 12.1X46-D15.3 #0: 2014-02-26 01:06:38 UTC
    [email protected]:/volume/build/junos/12.1/service/12.1X46-D15.3/obj-octeon/junos/bsd/kernels/JSRXNLE/kernel
real memory  = 1073741824 (1024MB)
avail memory = 559992832 (534MB)
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
Security policy loaded: JUNOS MAC/pcap (mac_pcap)
Security policy loaded: JUNOS MAC/runasnonroot (mac_runasnonroot)
netisr_init: !debug_mpsafenet, forcing maxthreads from 2 to 1
cpu0 on motherboard
: CAVIUM's OCTEON 5020 CPU Rev. 0.1 with no FPU implemented
        L1 Cache: I size 32kb(128 line), D size 8kb(128 line), sixty four way.
        L2 Cache: Size 128kb, 8 way
obio0 on motherboard
uart0: <Octeon-16550 channel 0> on obio0
uart0: console (9600,n,8,1)
twsi0 on obio0
dwc0: <Synopsis DWC OTG Controller Driver> on obio0
dwc_otg_core_reset() HANG! Soft Reset GRSTCTL=80000001
dwc_otg_core_reset() HANG! Soft Reset GRSTCTL=80000001
usb0: <USB Bus for DWC OTG Controller> on dwc0
usb0: USB revision 2.0
uhub0: vendor 0x0000 DWC OTG root hub, class 9/0, rev 2.00/1.00, addr 1
uhub0: 1 port with 1 removable, self powered
cpld0 on obio0
pcib0: <Cavium on-chip PCI bridge> on obio0
Disabling Octeon big bar support
PCI Status: PCI 32-bit: 0xc041b
pcib0: Initialized controller
pci0: <PCI bus> on pcib0
pci0: <simple comms> at device 1.0 (no driver attached)
pci0: <serial bus, USB> at device 2.0 (no driver attached)
pci0: <serial bus, USB> at device 2.2 (no driver attached)
gblmem0 on obio0
octpkt0: <Octeon RGMII> on obio0
cfi0: <AMD/Fujitsu - 4MB> on obio0
octpkt_attach: Initializing octpkt0 interface
Timecounter "mips" frequency 400000000 Hz quality 0
###PCB Group initialized for udppcbgroup
###PCB Group initialized for tcppcbgroup
md0: Preloaded image </isofs-install-srxsme> 10014720 bytes at 0x80e99268
Trying to mount root from cd9660:/dev/md0
WARNING: preposterous time in file system
WARNING: clock 4565 days greater than file system time
tty: not found
Starting JUNOS installation:
    Source Package: net0:/junos-srxsme-12.1X46-D15.3-domestic.tgz
    Target Media  : internal
    Product       : srx210h
ERROR: Target media /dev/da0 does not exist
Waiting (max 60 seconds) for system process `vnlru' to stop...done
Waiting (max 60 seconds) for system process `vnlru_mem' to stop...done
Waiting (max 60 seconds) for system process `bufdaemon' to stop...done
Waiting (max 60 seconds) for system process `syncer' to stop...
Syncing disks, vnodes remaining...0 0 0 0 0 0 0 0 done

syncing disks... All buffers synced.
Uptime: 16s
Rebooting...
cpu_reset: Stopping other CPUs