Forum

exchange2003 servic...
 
Bildirimler
Hepsini Temizle

exchange2003 service port numaraları

3 Yazılar
3 Üyeler
0 Reactions
626 Görüntüleme
(@LEVENTSENGECAL)
Gönderiler: 187
Reputable Member
Konu başlatıcı
 

Kolay gelsin arkdaşlar.


ad üzerinde olan bir sistemde trendmicro officescan 8.0 kullanıyorum..officescan içerisinde bulunan firewall setting ayarlarını yaptığımda exchange2003 server a bağlanamıyorum (hem uzak masaüstü hemde mailboxlara). ancak ayarlar içerisinde uzakmasaüstü portuna izin vermeme ve sistem içinde bulunan diğer tüm server lara uzak masaüstü bağlanabilmeme rağmen exchange olan server a bağlanamıyorum. uzak masaüstü 3389 portuna pop3 110, smtp 25 ve ımap4 993 portlarına allow yetkisi verdim. tüm diğer serverlar sorunsuz çalışıyor ama exchange ne uzak masaüstü nede http://xxxxxxx/excahnge çalışmıyor.


exchange nin düzgün çalışması için firewall altında hangi servislerin hangi portlarına izin vermeliyim. birde trendmicro firewall ayarlarını bulabileceğim bir kaynak varmı.


iyi çalışmalar..

 
Gönderildi : 18/03/2009 12:33

(@bugrakeskin)
Gönderiler: 5088
Illustrious Member
 

Protocol: LDAP

  • Port (TCP/UDP): 389 (TCP)

  • Description: Lightweight Directory Access Protocol (LDAP), used by
    Active Directory, Active Directory Connector, and the Microsoft
    Exchange Server 5.5 directory.

Protocol: LDAP/SSL

  • Port (TCP/UDP): 636 (TCP)

  • Description: LDAP over Secure Sockets Layer (SSL). When SSL is enabled, LDAP data that is transmitted and received is encrypted.

  • To enable SSL, you must install a Computer certificate on the domain controller or Exchange Server 5.5 computer.

Protocol: LDAP

  • Port (TCP/UDP): 379 (TCP)

  • Description: The Site Replication Service (SRS) uses TCP port 379.

Protocol: LDAP

  • Port (TCP/UDP): 390 (TCP)

  • Description: While not a standard LDAP port, TCP port 390 is the
    recommended alternate port to configure the Exchange Server 5.5 LDAP
    protocol when Exchange Server 5.5 is running on a Microsoft Windows
    2000 Active Directory domain controller.

Protocol: LDAP

  • Port (TCP/UDP): 3268 (TCP)

  • Description: Global catalog. The Windows 2000 Active Directory
    global catalog (which is really a domain controller "role") listens on
    TCP port 3268. When you are troubleshooting issues that may be related
    to a global catalog, connect to port 3268 in LDP.

Protocol: LDAP/SSL

  • Port (TCP/UDP): 3269 (TCP)

  • Description: Global catalog over SSL. Applications that connect to
    TCP port 3269 of a global catalog server can transmit and receive SSL
    encrypted data. To configure a global catalog to support SSL, you must
    install a Computer certificate on the global catalog.

Protocol: IMAP4

  • Port (TCP/UDP): 143 (TCP)

  • Description: Internet Message Access Protocol version 4, may be used
    by "standards-based" clients such as Microsoft Outlook Express or
    Netscape Communicator to access the e-mail server. IMAP4 runs on top of
    the Microsoft Internet Information Service (IIS) Admin Service
    (Inetinfo.exe), and enables client access to the Exchange 2000
    information store.

Protocol: IMAP4/SSL

  • Port (TCP/UDP): 993 (TCP)

  • Description: IMAP4 over SSL uses TCP port 993. Before an Exchange
    2000 server supports IMAP4 (or any other protocol) over SSL, you must
    install a Computer certificate on the Exchange 2000 server.

Protocol: POP3

  • Port (TCP/UDP): 110 (TCP)

  • Description: Post Office Protocol version 3, enables
    "standards-based" clients such as Outlook Express or Netscape
    Communicator to access the e-mail server. As with IMAP4, POP3 runs on
    top of the IIS Admin Service, and enables client access to the Exchange
    2000 information store.

Protocol: POP3/SSL

  • Port (TCP/UDP): 995 (TCP)

  • Description: POP3 over SSL. To enable POP3 over SSL, you must install a Computer certificate on the Exchange 2000 server.

Protocol: NNTP

  • Port (TCP/UDP): 119 (TCP)

  • Description: Network News Transport Protocol, sometimes called
    Usenet protocol, enables "standards-based" client access to public
    folders in the information store. As with IMAP4 and POP3, NNTP is
    dependent on the IIS Admin Service.

Protocol: NNTP/SSL

Port (TCP/UDP): 563 (TCP)

Description: NNTP over SSL. To enable NNTP over SSL, you must install a Computer certificate on the Exchange 2000 Server.

Protocol: HTTP

  • Port (TCP/UDP): 80 (TCP)

  • Description: Hyper-Text Transfer Protocol is the protocol used
    primarily by Microsoft Outlook Web Access (OWA), but also enables some
    administrative actions in Exchange System Manager. HTTP is implemented
    through the World Wide Web Publishing Service (W3Svc), and runs on top
    of the IIS Admin Service.

Protocol: HTTP/SSL

  • Port (TCP/UDP): 443 (TCP)

  • Description: HTTP over SSL. To enable HTTP over SSL, you must install a Computer certificate on the Exchange 2000 server.

Protocol: SMTP

  • Port (TCP/UDP): 25 (TCP)

  • Description: Simple Mail Transfer Protocol, is the foundation for
    all e-mail transport in Exchange 2000. The SMTP Service (SMTPSvc) runs
    on top of the IIS Admin Service. Unlike IMAP4, POP3, NNTP, and HTTP,
    SMTP in Exchange 2000 does not use a separate port for secure
    communication (SSL), but rather, employs an "in-band security
    sub-system" called Transport Layer Security (TLS).

Protocol: SMTP/SSL

  • Port (TCP/UDP): 465 (TCP)

  • Description: SMTP over SSL. TCP port 465 is reserved by common
    industry practice for secure SMTP communication using the SSL protocol.
    However, unlike IMAP4, POP3, NNTP, and HTTP, SMTP in Exchange 2000 does
    not use a separate port for secure communication (SSL), but rather,
    employs an "in-band security sub-system" called Transport Layer
    Security (TLS). To enable TLS to work on Exchange 2000, you must
    install a Computer certificate on the Exchange 2000 server.

Protocol: SMTP/LSA

  • Port (TCP/UDP): 691 (TCP)

  • Description: The Microsoft Exchange Routing Engine (also known as
    RESvc) listens for routing link state information on TCP port 691.
    Exchange 2000 uses routing link state information to route messages and
    the routing table is constantly updated. The Link State Algorithm (LSA)
    propagates outing status information between Exchange 2000 servers.
    This algorithm is based on the Open Shortest Path First (OSPF) protocol
    from networking technology, and transfers link state information
    between routing groups by using the X-LSA-2 command verb over SMTP and
    by using a Transmission Control Protocol (TCP) connection to port 691
    in a routing group.

Protocol: RVP

  • Port (TCP/UDP): 80 (TCP)

  • Description: RVP is the foundation for Instant Messaging in Exchange
    2000. While RVP communication begins with TCP port 80, the server
    quickly sets up a new connection to the client on an ephemeral TCP port
    above 1024. Because this port is not known in advance, issues exist
    when you enable Instant Messaging through a firewall.

Protocol: IRC/IRCX

  • Port (TCP/UDP): 6667 (TCP)

  • Description: Internet Relay Chat (IRC) is the chat protocol. IRCX is
    the extended version offered by Microsoft. While TCP port 6667 is the
    most common port for IRC, TCP port 7000 is also very frequently used.

Protocol: IRC/SSL

  • Port (TCP/UDP): 994 (TCP)

  • Description: IRC (or Chat) over SSL. IRC or IRCX over SSL is not supported in Exchange 2000.

Protocol: X.400

  • Port (TCP/UDP): 102 (TCP)

  • Description: ITU-T Recommendation X.400 is really a series of
    recommendations for what an electronic message handling system (MHS)
    should look like. TCP port 102 is defined in IETF RFC-1006, which
    describes OSI communications over a TCP/IP network. In brief, TCP port
    102 is the port that the Exchange message transfer agent (MTA) uses to
    communicate with other X.400-capable MTAs.

Protocol: MS-RPC

  • Port (TCP/UDP): 135 (TCP)

  • Description: Microsoft Remote Procedure Call is a Microsoft
    implementation of remote procedure calls (RPCs). TCP port 135 is
    actually only the RPC Locator Service, which is like the registrar for
    all RPC-enabled services that run on a particular server. In Exchange
    2000, the Routing Group Connector uses RPC instead of SMTP when the
    target bridgehead server is running Exchange 5.5. Also, some
    administrative operations require RPC. To configure a firewall to
    enable RPC traffic, many more ports than just 135 must be enabled.

For additional information, click the article numbers below to view the articles in the Microsoft Knowledge Base:

148732 XADM: Setting TCP/IP Port Numbers for Internet Firewalls

161931 XCON: Configuring MTA TCP/IP Port # for X.400 and RPC Listens

Protocol: T.120

  • Port (TCP/UDP): 1503 (TCP)

  • Description: ITU-T Recommendation T.120 is a series of
    recommendations that define data conferencing. Data conferencing is
    implemented on the server side as a Conferencing Technology Provider
    (CTP) in the Multipoint Control Unit (MCU), which is one component of
    the Exchange Conferencing Services (ECS). Data conferencing is
    implemented on the client side as Chat, Application Sharing,
    Whiteboard, and File Transferring in Microsoft NetMeeting.

Protocol: ULS

  • Port (TCP/UDP): 522 (TCP)

  • Description: User Locator Service is a type of Internet directory
    service for conferencing clients, such as NetMeeting. Exchange 2000
    Server and Exchange 2000 Conferencing Server do not implement a ULS,
    but rather take advantage of Active Directory for directory services
    (by TCP port 389).

Protocol: H.323 (Video)

  • Port (TCP/UDP): 1720 (TCP)

  • Description: ITU-T Recommendation H.323 defines multimedia
    conferencing. TCP port 1720 is the H.323 (video) call setup port. After
    a client connects, the H.323 server negotiates a new, dynamic UDP port
    to be used for streaming data.

Protocol: Audio

  • Port (TCP/UDP): 1731 (TCP)

  • Description: Audio conferencing is enabled in much the same way as
    H.323 video conferencing is enabled in Exchange 2000 Server. After
    clients connect to TCP port 1731, a new dynamic port is negotiated for
    further streaming data.

Protocol: DNS

  • Port (TCP/UDP): 53 (TCP)

  • Description: Domain Name System (DNS) is at the heart of all of the
    services and functions of Windows 2000 Active Directory and Exchange
    2000 Server. You cannot underestimate the impact that a DNS issue can
    have on the system. Therefore, when service issues arise, it is always
    good to verify proper name resolution.

 
Gönderildi : 18/03/2009 15:00

(@cozumpark)
Gönderiler: 16307
Illustrious Member Yönetici
 

merhabalar


buğra arkadaşımız portlarla ilgili detayları vermiş.


benim önerim ise ; trenmicronun kullandığı portları değiştirmenizdir. trendmicro ile ilgili bu tür sorunlar yoğunlukla karşılaşılan sorunlardır.


trendmicronun kullandığı portları değiştirip tekrar deneyin.


kolay gelsin

 
Gönderildi : 18/03/2009 16:16

Paylaş: